Mosquito Magnet® Liberty Plus
Important Tips
- Moving the Mosquito Magnet®
- When should you use the Quick Clear Valve?
- What size CO2 cartridge to use with the Quick-Clear Valve.
- Why is placement so important?
- How to check if you have a good vacuum.
- Can I use a gas gauge so I know when my tank is empty?
Moving the Mosquito Magnet®.
Placement of the Mosquito Magnet® is very important for an effective mosquito catch. If you need to move your trap for lawn maintenance, you MUST disconnect the regulator from the tank and remove the tank from the stand. There is a good chance your tank will fall off of the stand if you move the Mosquito Magnet® with the tank attached. If the regulator assembly is damaged while you are moving the trap it IS NOT covered by the warranty and there is a charge to replace this part.
It is recommended that you use the Quick-Clear Valve before and after any prolonged storage period. We also recommend that the cartridges are used every single propane tank change If you have problems starting your Mosquito Magnet® or keeping the Mosquito Magnet® running this is the perfect time to use a cartridge.
This will prevent any contaminants from building up in the fuel system of the Mosquito Magnet®. These contaminants may build up over time, clogging the fuel system, and causing trap failure. For additional maintenance, you can use the Quick-Clear Valve after every tank change; this will help prevent problems.
Where is the Quick-Clear Valve? Click Here.
We recommend that you use our exclusive, Extra Large Co2 Cartridges to
1) Remove Residue from inside your Mosquito Magnet and
2) Keep your Mosquito Magnet operating at peak performance
We currently have an internet-only sale on these items. To see the limited time offer click here.
These can be purchased by calling toll free, 1.800.214.7721.
Heavy Duty Quick-Clear Adapter
For a printable version of the standard Quick-Clear Valve instructions Click here.
Placement of the Mosquito Magnet® is a key element in how it works. If it is not placed properly there is the potential for a low catch or no catch at all. Click here for further assistance with placement.
How to check if your Mosquito Magnet has a good vacuum.
To check for sufficient vacuum you need to hold a piece of tissue, about half the size of a dime, under the opening of the trumpet-shaped part under the green housing. Place the piece of tissue about a half inch into the trumpet-shaped part. The arrows in the picture below show where to hold the tissue. Release the tissue, and it should get sucked up towards the trap. It may not get vacuumed all the way in through trap and into the net. Mainly you are looking to verify that there is air current moving in the right direction. The vacuum may not seem very strong, but keep in mind we are only trying to pull in a very tiny insect.
Can I use a gas gauge so I know when my tank is empty?
It is not recommended that you use a propane tank gauge which is placed in line between the propane tank and the Mosquito Magnet® regulator, (similar to the one pictured). The Mosquito Magnet® requires a very precise pressure and flow of propane at all times. These gauges may restrict the propane flow and cause the trap not to function properly. These gauges have not been tested with the Mosquito Magnet®.
When our regulators and gas lines are built they are thoroughly cleaned to greatly reduce any contaminants in the system and to prevent clogging of any kind. There may be contaminants in the gauge, or in the O rings used in the manufacturing of the propane tank gauge. These contaminants may get into the fuel system and possibly cause a clog. This will prevent your trap from functioning properly and may eventually prevent it from starting.
The best way to know when your propane tank is empty is to mark on a calendar the day that you refilled the tank and restarted the trap. Then count 21 days from that date. That will be your maintenance and refill date. The Mosquito Magnet® uses less than 1 pound of propane a day and will consume a full tank in about 18 to 22 days.